1. So, please, decide now to deliberately limit the time and attention you spend on "low yield" relationships.
所以，请现在就有意识地限制对“低产”关系花的时间和注意力。
来自互联网
2. But it has clearly reached a limit in creditors' willingness to supply funding at a reasonable yield, and may have reached the limit of taxpayers' willingness to pay the eventual bill.
3. Fatigue strength is less than static stress strength such as elasticity limit, yield strength.
疲劳强度低于弹性极限或屈服强度等静应力强度。
来自互联网
4. Silicon can obviously improve the elastic limit, yield point and tensile strength of steel.
硅能显著进步钢的弹性极限，屈从点和抗拉强度，故普遍用于作弹簧钢。
来自互联网
5. In two and three dimensions the yieldlimit is reached when a certain function of all the stress components reaches a fixed value.
在二维或三维的情况下，屈服极限是当所有应力分量的某个函数达到某一固定值时达到的。
来自互联网
6. The incipient yield pressure of the cylinder is gained by analyzing the experimental data, and then the limit of yielding is gained.
通过对该实验数据的分析得到了圆筒的初始屈服压力，最终求得了材料的屈服极限。
来自互联网
7. The aim is to obtain a high yield strength, elastic limit and high toughness.
其目的是获得高的屈服强度，弹性极限和较高的韧性。
来自互联网
8. Increasing the yieldlimit of high strength steel, and increasing the depth of submergence, the form of the differential equation's result will not only be limited with the complex number.
由于高强度钢材的屈服极限不断地增大，下潜深度的不断增加，弯曲微分方程解的形式将不仅限于复数解。
来自互联网
9. These factors in the near future there will be no fundamental change, will limit the total assets of China's banking yield level.
上述因素在近期内不会有根本性的改变，仍将限制我国银行的总资产收益率水平。
来自互联网
10. Consequently, the limit damping force of the unequal model proves the peak damping force (yield shear force) of the equal model.
证明了非均匀模型的极限阻尼力是均匀模型的最大阻尼力(屈服剪力)。
来自互联网
11. Its resilience is strong during shaping, because titanium's ratio of yieldlimit to elasticity modulus is high.
由于钛的屈服极限与弹性模量的比值大，使钛成型时的回弹能力大。
来自互联网
12. To make automobile panel rapidly and accurately, the yieldlimit, hardening modes and invalidation modes of materials for large automobile panels were analyzed.
13. The initial yield pressure of the cylinder is gained by analyzing the experimental data, and then the yield limit is calculated.
通过对该试验数据的分析得到了圆筒的初始屈服压力，最终求得了材料的屈服极限。
来自互联网
14. Because the analyte molecules are recognized by forming the binding complex with antibody, a decrease in the detection limit is achieved only by an increase in the reaction yield.
因为分析物分子能通过与抗体形成结合物而被发现，所以降低检测极限只能通过增加反应产率来达到。
来自互联网
15. A proposed method is presented to design lead shear dampers according to the limit damping forces and yield displacements.
以极限阻尼力和屈服位移为参数，给出了阻尼器的设计方法。
来自互联网
16. The distingUishing featUres of the paper are the influences of line loads on models of yield line, the method of selecting strips, and the method of the limit analysis of the slab under line loads.
文章的主要特点为线荷载对屈服模式的影响，条带的选取方法，线荷载作用下板的极限分析方法。
来自互联网
17. The strain yield locus of the stress yield criterion was advanced and the strain ellipse method for calculating the limit bulging coefficient was given.
提出应力屈服条件的应变屈服轨迹，给出了复合胀形极限成形系数的解法；
来自互联网
18. Other he may maximum limityield.
别的他可以最大限度让步。
来自互联网
19. The yield criterion of composite materials is simulated by using the homogenization method of micromechanics and the plastic limit analysis theory.
运用细观力学中的均匀化方法和塑性力学中的极限分析理论，分析了复合材料的屈服准则。
来自互联网
20. Soil salinity is one of chief environmental factors that limit the crop yield potential.
土壤盐渍化是降低农作物产量的主要环境因素之一。
来自互联网
21. It is the fine cementation of microcracks so as to reduce or eliminate the stress concentration on their ends intensively. Thus, the limityield of rock mass and its strength are both enhanced.
微细裂隙的良好胶结，使其端部应力集中被降低或消除，岩体屈服极限增大，强度提高。
来自互联网
22. Under the instantaneous strain and yieldlimit calculated, judgement rule about viscoelastic and viscoplastic is established.
通过计算瞬时应变的大小与屈服限建立粘弹性变形和粘塑性变形的判断准则。
来自互联网
23. The wheat leaf is the main organ for photosynthesis. The decline of assimilation induced by leaf senescence may limityield potential.
叶片是小麦进行光合作用的重要器官，其衰老引起的叶片同化功能减退限制了小麦产量潜力的发挥。
来自互联网
24. Though the peak value of the stress in part areas exceeds the yieldlimit of the cast steel, as the yielding areas are small an.
25. The characteristic line method meets the static equilibrium equations and yield conditions, which gives the lower limit of the solutions.
本方法满足静力平衡方程和屈服条件，属于极限分析理论的下限解。
来自互联网
26. The most dangerous point is at the root of the first engaged tooth of a joint. Generally, the biggest values of stress and strain may exceed the yieldlimit.
最危险点在接头的第一啮合齿的齿根处，最大应力应变值一般均超过屈服极限。
来自互联网
27. In the plastic limit analysis, the wrinkler's plate is smartly analyzed in yield-line theory to get the critical compression strength of the coal pillar.
