2. Too high switch point: empty part, weldline, sink mark, and small.
转压点太高：产品充模不足，熔接痕，凹陷，尺寸偏小等。
来自互联网
3. Weld Area crack. A crack in or immediately adjacent to the weld line.
焊缝区裂纹。在焊缝线或紧靠焊缝线出现的裂纹。
来自互联网
4. In engineering, in order to make the weldline even and reliable, it is needed to cut the weld opening accurately.
工程上，为了使钢管相贯处焊缝均匀，焊接可靠，需要将钢管的焊口准确切割成型。
来自互联网
5. The trajectory planning of posture adjustment is presented for a weld mobile robot during auto-searching weld line.
主要研究移动焊接机器人在自寻迹过程中位姿调整的轨迹规划。
来自互联网
6. In the tracking trials of sidelong, reflex and curve weld line, the system can all meet the demand of the tracking precision.
在斜线、折线和曲线三种不同形状待焊焊缝的跟踪试验中，系统都能满足药芯焊丝水下自动焊接的要求。
来自互联网
7. But injection molding often results many product's problems such as short shots, overflow edges, warp, weldline, dimension error and so on.
但是，注塑成型常常出现各种质量问题，例如，短射、飞边、翘曲、熔接痕和尺寸误差等。
来自互联网
8. By comparing analysis results, the best moulding project is chosen filling effect being unifor with unobvious weldline and centralizing air traps.
通过比较分析结果，选择出填充效果均匀、熔接痕位不明显、气穴位置集中的较好成型方案。
来自互联网
9. Drop transfer in the process of MIG welding is very complicated and quality of weld line is easily impacted by welding parameters coupled with each other.
MIG焊过程熔滴过渡过程复杂，影响焊接质量的参数多，相互间耦合性强。
来自互联网
10. The peculiarity and error of CAE were analysed, and corresponding control measures for the weldline were proposed according to different affecting factors.
分析了熔接痕CAE的特点及误差，并针对不同影响因素，给出了相应控制对策。
来自互联网
11. Contact mark. Intermittent marks adjacent to the weldline resulting from the electrical contact between the electrodes supplying the welding current and the pipe surface.
触点痕。由于供焊接电流的电极与管子表面间的电接触，致使在焊缝线附近产生不连续痕迹。
来自互联网
12. Detecting the weldline and its edge directly by visual sensor can achieve much useful information, which is very important in the research of weldline automatic tracking.
13. The drop simulation for the front plastic shell have been done with take the position of weld line which result from the two relatively optimal projects to the lowest location.
②塑料件前壳试验：将两组较优浇口方案产生的熔接痕位置调整到跌落方向的最低处。
来自互联网
14. This article introduces the technological method of using glass fibre tubes to solve the splitting problem from the weldline after the forming of the thermosetting product "pedestal".
前言：利用玻璃纤维套管，解决了热固性塑料制件“底座”成型后从熔接线处开裂的问题。
来自互联网
15. With the FEM modeling for the curved weldline TWBs, the paper makes the comparison of linear and nonlinear weld line TWBs, which can help to offer the reference for the engineering application.
16. If you have been careful when marking out and cutting the parts outlined on page one these parts should all line up accurately ready to weld.
如果你一直小心划出和削减第一页上的这些部分都应该准确地排队准备焊接概述的部分。
来自互联网
17. The fatigue crack propagation rate of the fusion line and weld toe are greater than that of the others.
熔合线和焊趾处疲劳裂纹扩展速率较其他部位大。
来自互联网
18. Based on the fracture site investigation and macro-rod fracture analysis, the welding rod fracture occurred in the vicinity of the weld fusion line.
通过对最近的一次断裂拉杆现场调查和宏观断口分析，发现断裂发生在拉杆的补焊焊缝熔合线附近。
来自互联网
19. The result shows that the bond between surfacing weld and base metal is metallurgical bond, and bond line is clear.
结果表明，喷焊层与基体是冶金结合，结合线清晰。
来自互联网
20. The longitudinal cracks along bond line and the transverse cracks which cut across the weld metal cross section inside weld metal were formed, while X65 pipe line steel was welding.
21. The development procedure of the milling machine on line used in production of weld H type section steel was described in details, including the design idea, structure mode and working principle.
22. Through material, weld material, weld technology. Analyses the reason when cracking-fusion product in line pan. Introduces a method of preventing cracking-fusion production.
23. Cracks were found at internal weld toes of the pipes of Fo-Liang gas transporting line.
佛两线天然气输送管道检测与评价时，发现管道内焊趾多处开裂。
来自互联网
24. The Beamlet transform was introduced to detect the line segment characteristic of the structured light in the image to identify the position of the weld seam effectively.
为有效提取图像中结构光线性特征以确定焊缝位置，引入了束波变换。
来自互联网
25. Control of the penetration and width of the back side weld was then achieved by controlling the width of an isothermal line near the melting point.
通过控制接近熔点温度的等温线宽度最终实现了对焊缝背面熔宽和熔透的控制。
来自互联网
26. The Model SPC/L301 viscometer has a 1 1/4" NPT thread to easily install into a process line using a "Tee", or into a large tank or pipe, using a weld ferrule.
27. The Model SPC/L301 viscometer has a 1 1/4" NPT thread to easily install into a process line using a "Tee", or into a large tank or pipe, using a weld ferrule.
