10. The shape defect is decreased with increasing sheet thickness, increasing binder force, decreasing yield strength, and decreasing curvatureradius.
形状不良随板料厚度的增加、压边力的增加、屈服强度的降低、凸模曲率半径的减小而减小。
来自互联网
11. Spherical curvatureradius was optimized through controlling the exit rays and using the automatic optimization function of optical design software.
通过对出射光线的控制，利用光学设计软件的自动优化功能，优化出满足条件的球面曲率半径。
来自互联网
12. 2 the curvatureradius and the change curve of the transition fillet at the shoulder of the input shaft of the reducer are not carefully considered.
2减速机输入轴处轴肩处未细致考虑过渡圆角的曲率半径和变化曲线使应力集中严重发生疲劳破坏。
来自互联网
13. The curvatureradius was derivated and the contact stress of the three-arc-sect isometric type surface was calculated through the elastic dynamics theory.
应用弹性力学理论，推导出接触点的曲率半径，对三弧段等距型面联接进行接触应力计算。
来自互联网
14. The result shows that with the decrease of the curvatureradius, the peak value of intensity and the facula decrease slightly, however the stability is still higher.
结果表明随着输出镜曲率半径的减小，光强峰值和光斑大小有轻微减小，稳定性更高。
来自互联网
15. After unloading and resiling, the curvatureradius of CT decreases monotonously along with stretch increasing. As a result, stretch is helpful to reducing resilience.
16. The data transform program has been compiled with MATLAB, which sequentially finishes transformation of part curvatureradius into control coordinate of machine tool.
用MATLAB编写了数据转化程序，完成了变曲率零件从型值点的曲率半径到机床控制坐标的转换。
来自互联网
17. Based on the analysis of geometry parameters and contact stresses of the deep groove ball bearings, the control equation of groove curvatureradius has been drawn out.
18. Using the changing rate of maximum feed-rate as a threshold, the surface of the part is divided into different areas according to the values of normal curvatureradius.
以最大工作进给速度的变化比率为阈值，把零件表面的法曲率半径划分为不同的区域；
来自互联网
19. Solutions such as decreasing the tool's curvatureradius, using means of single dimensional numerical control compensation or profiling with a hollow cone are effective.
解决方法是减小工具的曲率半径，或增加一维数控进行补偿，或使用空心圆锥体仿形。
来自互联网
20. The motion of charged particle acted upon by Lorentz force and other external force are analyzed, calculating formulae of orbit equation and curvatureradius are derived.
分析了带电粒子受到洛伦兹力和其他恒定外力作用下的运动情况，导出了轨道方程和曲率半径的计算公式。
来自互联网
21. The differences of stress state between extrusion-flanging and traditional flanging, and the influences of curvatureradius of burring punch on flange height were analyzed.
分析了挤压翻边与传统翻边应力状态的不同之处，以及翻边凸模的冲头曲率半径对翻边效果的影响。
来自互联网
22. The effects of the curvatureradius, the transmission of output coupler, the spot size of the pump, and the temperature of the heat sink on the output power are investigated.
对输出镜的曲率半径、输出镜透过率、泵浦光斑大小以及热沉温度对激光器输出功率的影响也作了研究。
来自互联网
23. The line width of nanostructures is influenced by many factors such as tip curvatureradius, detained time in the base surface, scanning speed, humidity, surface roughness etc.
尖端曲率半径、针尖在基底表面滞留时间、针尖扫描速度、空气湿度、表面粗糙度等均会影响纳米结构的线宽。
来自互联网
24. In the production practice, this problem should be kept in mind and resolved by programming for compensating the variation of tool nose curvatureradius and removing the error.
在实际生产中要加以注意，并通过编程以补偿刀尖圆弧半径的变化，消除误差，使问题得以解决。
来自互联网
25. Based on the minimum curvatureradius definition and mid value theorem, the pape gives the method of determining the limit load of pile foundation through extreme value analysis.
文章根据最小曲率半径定义和中值定理，通过极值分析方法来确定桩基极限荷载。
来自互联网
26. This paper first analyzes the reason of the aliasing and the common methods for anti aliasing, and then proposes a method for adaptive anti aliasing based on the curvatureradius.
27. It shows that with the increasing of curvatureradius, liner thickness, the length-to-diameter ratio of the charge, and decreasing of shell thickness, the velocity of EFP increase.
结果表明：随着药型罩曲率半径、装药长径比、壳体厚度的增大以及药型罩壁厚减少，EFP的速度增大。
来自互联网
28. In track simulation, the corresponding earth equivalent radius of a track in a specific range is approximate to the earth curvature radius of the latitudinal location of the target.
29. In track simulation, the corresponding earth equivalent radius of a track in a specific range is approximate to the earth curvature radius of the latitudinal location of the target.
