1. I smiled, small SanNeng centralizer, the devil angel's wings.
我笑了，小三能扶正，魔鬼都能长出天使的翅膀。
来自互联网
2. Many nations have issued the norms of computing centralizer intervals.
很多国家都颁布了套管扶正器间距计算规范。
来自互联网
3. This method has developed the software to design the centralizer arr...
该方法已研制成软件，可以对聚驱抽油机井杆柱扶正进行设计。
来自互联网
4. The design of centralizer assembly is the basic and key job for directional drilling.
扶正器组合设计是钻定向井基本而关键的工作。
来自互联网
5. This proves one half of the double centralizer properties. Another half was obtained by s.
这证明了一半的双重中心化子性质，另一半已由S。
来自互联网
6. The tubing centralizer worked by hydraulic, solved the problem of tubing screw deflection and met the need of production.
该扶正器采用液压式扶正，解决了油管偏螺纹这一难题，满足了生产的需要。
来自互联网
7. The current centralizer has such defects as being apt to tire and wear off, worse seal and the wasting of fluid resistance.
现有扶正器有易疲劳损伤、对接不严、流阻损耗的缺点。
来自互联网
8. Made up of oil expanding type or water expanding type expandable elastomer material, mechanical pipe string, centralizer and etc.
由油胀式或水胀式可膨胀弹性体材料与机械管柱、扶正器等构成。
来自互联网
9. The axial load and centralizer spacing from the bottom to the top are calculated by using the mechanical analysis method and the log data.
采用力学分析的方法，结合测井资料，由下到上计算了抽油杆柱的扶正器间距和轴向力。
来自互联网
10. It provides a reasonably and completely theoretical basis for combination of rods, centralizer, assembling site and number of depart device.
为抽油杆柱组合、扶正器、防脱器安放位置及数量设计提供了更加合理、完善的理论依据。
来自互联网
11. Optimization of Shaft Size and Centralizer Span of Single Screw Pump in Declined Oil Well. Chinese Journal of Computational Mechanics. 1(19):58-62.
12. The axial load and centralizer spacing from the bottom to the top are calculated by using the mechanical analysis method and the well trajectory data.
采用力学分析的方法，结合井眼轨迹数据，由下到上逐跨计算了抽油杆柱的扶正器间距和轴向力。
来自互联网
13. The pump efficiency of 32% rod pumped Wells in Erlian Oilfield is lower than 30%, and increasing production centralizer is introduced to solve this problem.
二连油田有32%的抽油机井泵效低于30%，为此有针对性地引进了增抽扶正器配套工艺。
来自互联网
14. Furthermore, since the drugs attack power and extreme damage justice, it must strictly adhere to the dose used, centralizer with drugs or with the application.
此外，由于本类药物攻伐力强，极易损伤正气，故使用时必须严格掌握其剂量，或与扶正类药物配合应用。
来自互联网
15. This paper derives the equation, describes the use of centralizer assembly taking the well Zhong-48 as an example and presents the attentions for appling this method.
本文推导了计算公式，并以中48井为例，叙述了扶正器组合的使用，提出了采用此法应注意的事项。
来自互联网
16. As the eccentric wear of pumping rods occurs in the high Angle deviated intervals with higher probability, so centralizer should be taken technical measure as encryption.
大斜度井段抽油杆发生偏磨的概率较大，应采取扶正器加密的技术措施。
来自互联网
17. The pipe string includes double hydraulic cylinder with anchorage packer, double hydraulic cylinder without anchorage packer, releasing tool, reversing valve and centralizer.
18. On the basis of the theoretical and experimental research, the preventive measures are discussed such as installing tubing anchor, rotary device of rod string and centralizer.
19. According to the theory equation of bend beam, using the computer to solve the performance parameters in the design of centralizer assembly is a new, simple and reliable method.
根据纵横弯曲梁理论公式，用计算机求解性能参数进行扶正器组合设计，是简便可靠的新方法。
来自互联网
20. The adjustment of the cable channel, wireless channel, centralizer and management software has been carried on in laboratory environment, and the result shows the feasibility of the entire designing.
21. A kind of device which can keep the casing at the center of borehole and can also generate helical flow of cement slurry, which is the Spring Whirlflow casing Centralizer, is presented in this paper.
提供了一种既能保证套管居中，又能产生水泥浆环空螺旋流的套管弹性旋流扶正器。
来自互联网
22. It is designed specifically to replace a solid body type centralizer for casing running applications and severe well geometries when run in horizontal, long ERD, J-type, S-type and other well designs.
23. The dynamic strength of rod string and the mount position of centralizer were calculated, according to the acquired deformation of rod string and its impact contact force with tube in the time domain.
根据求得的时域内抽油杆柱受力变形值以及与油管柱碰撞接触力，计算了抽油杆柱动强度和扶正器安放位置。
来自互联网
24. The dynamic strength of rod string and the mount position of centralizer were calculated, according to the acquired deformation of rod string and its impact contact force with tube in the time domain.
