Unscrew axle and left axle end, then remove bearing.
youdao
2. 筒体与轴两端的相连处装有四重轴端密封装置。
Two ends of the mixing axis that articulates with the mixing silo are loaded quadruple axle end seal device.
youdao
3. 两侧生裂片与两侧生小叶径向排列，位于近轴端。
Two adnate shatters and two adnate leafits are radial range, and they locate in the end near axle.
youdao
4. 注1设计时，请注意使两个轴端不超过丝杠轴底径。
Note 1 the diameter of the Screw Shaft both ends must be less than the Screw Shaft Root diameter.
youdao
5. 用于梳理机上的一种小滚筒类上的轴端挡飞花装置。
An axis end flying-blocking device used on a carding machine belongs to the small roller class.
youdao
6. 在逆止器的轴端孔内通过胀套和双平键与从 动轴连接；
The inner part of a shaft end hole of the backstop is connected with a driven shaft through an expansion bush and a double flat key;
youdao
7. 在垫体的两短轴端边，各设有一带齿眼的固夹耳（1）。
The edges of two short axis of the pad are respectively provided with a fixed clipping ear (1) with teeth points.
youdao
8. 阀门轴端与驱动器的连接平台符合ISO 5211标准。
Valve drive shaft connected with the platform in line with the ISO5211 standard.
youdao
9. kcb齿轮泵主要有齿轮、轴、泵体、安全阀、轴端密封所组成。
KCB gear pump are mainly gear, shaft, pump body, valve, shaft end seal.
youdao
10. 介绍了轴端螺栓紧固装置的设计方案、主要技术参数和性能特点。
Described are the design scheme, main technical parameters and performance features of the tightening device for bolts at the axle ends.
youdao
11. 零件上的花键孔与传动轴端部的花键轴相配合，用于传递动力之用。
Parts of the spline hole and the shaft end of the spline shaft of it, for power transmission purposes.
youdao
12. 针对离心通风机传动组的轴端密封经常漏油这一现象，提出了改进措施。
Improving measures are put forword against the phenomenon of shaft end seal of oil leakage of centrifugal fan driving unit.
youdao
13. 这样，转向节、转向节轴端、车轮和轮胎都会向一侧旋转，汽车实现转向。
Thus, the steering knuckle, spindle, wheels, and tires turn to one side, causing the car to turn.
youdao
14. 在芯轴端部 内侧设置滚针轴承，使整个轮毂单元的受力平衡，运转更平稳。
The internal of the core axle end is provided with a needle bearing, which balances the bearing of assembly wheel hub and enable the operating more stable.
youdao
15. 该机采用卧式粉碎机构，轴端设有配重轮，运转过程中不会产生“卡死”现象。
This machinery is a new type horizontal smash mechanism. It is equipped with kit rounds at the fore shaft, so it won't be blocked on the operation process.
youdao
16. 标准配置含轴端泵，现场应预留安装空间，若不能满足安装要求，请与厂家联系。
A shaft end pump should be included in the standard installation. The assembly space should be considered at site. Shall the installation not meet the requirement, please contact with the supplier.
youdao
17. 通过数值仿真和实验研究远轴端eord支承的单盘柔性转子系统的不平衡响应。
Numerical simulations and experimental investigates were carried out for unbalance response of a single disk flexible rotor system with far shaft end mounted on EORD.
youdao
18. 电子设备用电容电阻。单孔轴套安装轴动电子元件的轴端。轴套及装配最佳尺寸。
Capacitors and resistors for electronic equipment. Preferred dimensions of spindle ends, bushes and for the mounting of single-hole, bush-mounted, spindle-operated electronic components.
youdao
19. 介绍了150SBD-12型离心式砂石泵轴端密封的结构原理和相应的技术措施。
The principle and technique of sealing of shaft end of the 1150SBD-12 centrifugal gravel pump are introduced.
youdao
20. 卸刀时严谨敲打筒夹及刀头。运输、保管及使用中严谨磕碰、敲击、撞击电主轴轴端。
No beating the collet and cutter head in the process of unloading knife. No bumping, peening, striking the shaft end during the process of transporting, storing and using.
youdao
21. 用这种方法可以分析多种外界因素对齿轮啮合的影响，如箱体变形、轴端受力、轴线挠曲等；
This makes it possible to analyze the effect on gear mesh of such factors as gear box deformation, axial end loading and axial deflection, etc.
youdao
22. 本系列齿轮泵主要有齿轮、轴、泵体、安全阀、轴端密封所组成，齿轮油泵巩义市电话： 。
This series of gear pumps are gear, shaft, pump, safety valve, shaft seal formed.
youdao
23. 该搅拌机主要由搅拌筒体、搅拌轴及其轴端密封装置，以及主传动机构和卸料机构等部分组成。
Tthe mixer is primarily composed of mixing silo, mixing axis and their axle end seal device, main drive gear and discharging mechanism etc.
youdao
24. 主要有齿轮、轴、泵体、泵盖、轴承套、轴端密封等组成。齿轮采用双圆弧正弦曲线齿形制造。
YCB arc gear pumps are mainly gear, KCG axis, the pump body, cover, the axial bearing, sealing etc. Using double circular-arc gear tooth sine curve.
youdao
25. 常用的伺服电机是交流伺服电机，在电机的轴端装有光电编码器，通过检测转子角度用以变频控制。
Commonly used servo motor is ac servo motor, the motor shaft with in the photoelectric encoder, by detecting the rotor Angle to frequency conversion control.
Now commonly used servo motor is ac servo motor, the axial end in motor with photoelectric encoder, by examining the rotor Angle to frequency conversion control.
Pump shaft seal is designed to end in two forms, one for the mechanical seal, one is packing seal, may be based on specific usage and user requirements to determine.
The Nut Bracket is standardized for the standard Ball Screw assembly provided with finished shaft ends. It is designed to be secured directly on the table with bolts.
The Nut Bracket is standardized for the standard Ball Screw assembly provided with finished shaft ends. It is designed to be secured directly on the table with bolts.
