- 1. 筒体利用端盖支承在主轴承上。
- Cylinder using cover support on the main bearing.
youdao
- 2. 端盖将被用来作为轴承或旋转点。
- The end cap will be used as the bearing or swivel point.
youdao
- 3. 端盖准确地从精密加工方钢块。
- End caps are accurately machined from precision square steel blocks.
youdao
- 4. 电镀锌端盖及骨架，不易生锈。
- Zinc plated cap and center frame, good rust prevention performance.
youdao
- 5. 将末端端盖和保险杆分隔开。
- Separate the end cap from the bumper.
youdao
- 6. 安装连接末端端盖到前挡泥板的螺栓。
- Install the bolts attaching the end cap to the front fender.
youdao
- 7. 端盖要么髹黑漆标准或黑色环氧漆涂。
- End caps are either painted with standard black paint or painted with black epoxy paint.
youdao
- 8. 端盖-铝端盖提供坚固耐用。
- End caps - Aluminum end caps provide sturdiness and durability.
youdao
- 9. 端盖从加工精度准确方钢块。
- End caps are accurately machined from precision square steel blocks.
youdao
- 10. 仔细地检查漏水孔端盖与端座水的渗出量。
- Carefully check the amount of water seepage from the end cap and end bell weep hole.
youdao
- 11. 拆去连接末端端盖前面到部分板下侧的螺丝。
- Install the bolts attaching the end cap to the front fender.
youdao
- 12. 在扣件尾部和保险杆边缘外部定位末端端盖。
- Position the end cap on the rear of the retainer and the outer edge of the bumper.
youdao
- 13. 全面分析了减震器储油缸两端端盖的焊接特点。
- The welding characteristics on the double end cover of deoscillator stock tank are analyzed all-sidedly.
youdao
- 14. 本设计阐述了制造“轴封端盖”的复合模的设计。
- This design elaborated the manufacture "the axis seals the end cover" compound mold design.
youdao
- 15. 端盖用螺栓将它们固定在管板上并加入垫片密封。
- Cover is fixing on the tube plate with some sealed gasket by bolt.
youdao
- 16. 我有一些平板端盖焊接起来用腿和模具材料的淤塞。
- I had some flat plate end caps welded up to use as legs and mold material blockages.
youdao
- 17. 我想，即使作出修改的大会，将取代压载水舱端盖。
- I think I would even make a modified assembly that would replace the ballast tank end cap.
youdao
- 18. 世贸中心，其中被列入，但也有两个橡胶O型圈为端盖。
- The WTC which was included, there were also two rubber O-rings for the end caps.
youdao
- 19. 阀体和内部零件：阳极电镀铝合金、铜。加固端盖：塑料。
- Valve body and internal parts: anodized aluminum alloy, copper. Reinforcement Cover: Plastic.
youdao
- 20. 阀体和内部零件：阳极电镀铝合金、铜。加固端盖：塑料。
- Valve body and internal parts: anodized aluminum alloy, copper.
youdao
- 21. 建立了针对柱形真空杜瓦容器端盖密封结构的轴对称模型。
- An axial symmetrical model is set up for the sealing structure of the bulkhead plate for a columniform dewar.
youdao
- 22. 在分析端盖零件压铸工艺的基础上，论述了压铸模的设计要点。
- Based on analyzing die casting process of cover part, the authors discuss the main points of the design of die casting mould.
youdao
- 23. 在设计过程采用锥面制动端盖实现了工作状态和制动状态的互锁。
- In the design process using cone brake cover state and work to achieve a state of interlocking brake.
youdao
- 24. 为了承受高负荷，如在实际情况下，固体铸铁轴承端盖投入使用。
- In order to withstand high loads, as is found in practical circumstances, solid cast iron bearing end shields come into use.
youdao
- 25. 这反过来去，在另一层端盖和管道输送的石油与差距灌满水和冻结。
- That in turn went in another layer of end cap and pipe with the gap filled with water and frozen.
youdao
- 26. 本加热器是常用的管壳式换热设备，由端盖、壳体、管组和附件组成。
- The heater is a kind of used shell- and-tube heat exchanger which consists of head cover, Shell, nest of tubes and accessories.
youdao
- 27. 原木质地的建造材料和抛光金属端盖使建筑的“棱形形式”显得并不突兀。
- The structure's "prismatic form" is softened by the texture of the raw wood, along with end caps made of polished metal.
youdao
- 28. 为提高探测器的接收度，EMC在先前桶部设计的基础上增加了端盖部分。
- The end-cap EMC has been recently designed as a supplement to the previous barrel part in order to increase the acceptance.
youdao
- 29. 为提高探测器的接收度，EMC在先前桶部设计的基础上增加了端盖部分。
- The end-cap EMC has been recently designed as a supplement to the previous barrel part in order to increase the acceptance.
youdao
