2. Step 6: Duplicate the Star Diffusionlayer and group the two layers
第六步：复制星光柔化图层并另建包含这两图层的图层组
来自互联网
3. A gradient diffusionlayer exists between the layer and the matrix.
基体与熔凝层之间存在梯度扩散层。
来自互联网
4. Step 8: Apply the opposite diagonal motion blur to the other Star Diffusionlayer.
第八步：在另一个星光柔化图层上使用相反对角线的动态模糊效果。
来自互联网
5. The nitrided layer of pure iron consists of compound layer and diffusionlayer.
纯铁渗氮层则由化合物层和扩散层组成。
来自互联网
6. Using the X-ray diffraction setup, phases in the diffusionlayer were determined.
并用x -射线衍射对渗层相组成进行了分析。
来自互联网
7. Now select the other Star Diffusionlayer that you did not apply the motion blur effect to.
现在选择另一个还没有进行动态模糊效果的星光柔化图层。
来自互联网
8. The microstructure and the properties of nickel diffusionlayer were also investigated.
同时，对扩散层的组织和性能进行了研究。
来自互联网
9. The effect of ignition property on diffusionlayer in normal ambient temperature was examined.
研究了几个常用的环境温度下扩散层对点火性能的影响。
来自互联网
10. Rapid cooling after nitrocarburizing, martensite structure is obtained at the diffusionlayer.
氮碳共渗后快冷，在渗层获得含氮碳的马氏体组织。
来自互联网
11. The characteristics of so-called silicon diffusionlayer were analyzed through EPMA and hardness test.
通过成分分析（EPMA）和硬度测试， 分析了硅扩散层的特征。
来自互联网
12. It is the compostiton of bulk material and deposition temperature that mainly affects the diffusionlayer.
影响扩散层的主要因素是基体材料的成分和沉积温度；
来自互联网
13. Oxidation temperature has a more obvious effect on the thickening of oxygen diffusionlayer than time dose.
温度对于渗氧层厚度的影响大于时间的影响。
来自互联网
14. Test shows that the depth of residual compressive after chemical heat treatment is correspondent with that of diffusionlayer.
试验表明，化学热处理后残余压应力的深度往往与渗层深度相一致。
来自互联网
15. The relationships of chronoamperometric current and diffusionlayer with electrolysis time are discussed at microband electrode.
本文讨论了微带电极的计时电流、扩散层与时间的关系；
来自互联网
16. The effects of the voids in the diffusionlayer on cyclic oxidation and spalling resistance of aluminized steel was investigated.
研究了热浸渗铝钢扩散层空洞对循环氧化和剥落性能的影响规律及其机理。
来自互联网
17. The results show that the thickness of the diffusionlayer increases obviously with the increase of temperature and holding time.
结果表明，扩散层的厚度随烧结温度的提高和保温时间的延长而增厚。
来自互联网
18. Nitriding and oxidation: diffusionlayer and oxidation layer improve soldering resistance, adhesion resistance and crack resistance.
氮化扩散层和氧化层：可以提高模具耐溶损性、耐过烧性、耐粘着性和耐热裂性。
来自互联网
19. Properties of nitrided parts have close relation to phase composition of their compound layer and microstructure of their diffusionlayer.
渗氮件的性能与渗氮层的化合物相组成和扩散层的微观结构密切相关。
来自互联网
20. The calculating results of activation energy show that the diffusibility of nanometer Ni is better than Ni foil in diffusionlayer at joints.
通过计算接头处扩散层的激活能可知纳米镍的扩散性能比镍箔的好。
来自互联网
21. Phase transformation sequence in diffusionlayer and the existence of residual austenite have great effect on the distribution of residual stress.
渗层中的相变次序和残余奥氏体的存在对残余应力分布影响较大。
来自互联网
22. However, cracks initialized in the diffusionlayer between substrate and bond coat when TBCs were tested with low cycle fatigue at high temperature.
而在高温低周疲劳条件下裂纹是在粘结层与高温合金基体的扩散层处。
来自互联网
23. Part of their coating forms an alloy-like diffusion layer (about 1 mm) in the bulk of the metallic material, which is a great feature of this treatment.
部分合金涂层形式一样扩散层(约1毫米)在大部分的金属材料，这是一个伟大的特点，这种待遇。
来自互联网
24. Electrons are injected into the floating gate by applying a high voltage to the second impurity diffusionlayer in capacitive coupling with the floating gate.
通过在与浮栅电容耦合的第二杂质扩散层上施加高电压对浮栅注入电子。
来自互联网
25. The interface structure of composite consists of core material diffusionlayer, chilling solidified layer, directional growth layer, and cellular granular layer.
复合材料界面结构由芯材扩散层、激冷凝固层、方向性生长层和胞状晶粒层组成。
来自互联网
26. There is amorphous phase in diffusionlayer of the hot-dip La-aluminizing and the content of the amorphous phase increases due to the addition of rare earths la.
热浸镀铝-镧钢的扩散层中存在非晶态相，且稀土镧的添加可使扩散层中的非晶含量增加。
来自互联网
27. The results show that rare earth elements can efficiently improve the structures of the Chromvanadizing layer, the rate of growth and properties of diffusionlayer.
结果表明，稀土元素能有效地改善铬钒共渗层结构，提高共渗层生长速度和性能。
来自互联网
28. A new LT process was established after the preferred Selection of technology parameters, various examinations of properties of the diffusionlayer and production practices.
通过诸工艺参数的优选，扩散层性能的多方面考核和生产实践，确定了LT新工艺。
来自互联网
29. A first impurity diffusionlayer, which occupies a space within the semiconductor substrate, is provided separately apart from the floating gate by a predetermined distance.
在浮栅的两侧壁上，设置侧壁绝缘膜。第一杂质扩散层设置在半导体基板内，并与浮栅仅离规定的距离。
来自互联网
30. The relationship of the process parameters to the depth of diffusion, concentration of titanium in the diffusion layer and the microstructure of titanizing layer are studied.
